Holley Carb Parts

Busted Knuckles: 1964 Ford F100

Building classic trucks can present some unique challenges to the builder. Since they have been around longer, there is more of a chance of severe oxidation, accident damage, and several other problems, which will, hopefully, be discovered during teardown. David Cross, of Anderson, South Carolina, ran into some of these challenges when building his 1964 Ford F-100. He originally owned a ’64 with 120,000 miles on it, and began building a frame from another F-100 that he could swap that donor truck’s engine and transmission into. Well, as things would have it, the front of the frame he bought had been damaged in an accident. So he bought another frame, and the back of that frame had been damaged also. After several different purchases and some choice words, David eventually had all the parts he needed to build the truck to completion. The parts came from about seven different trucks, but at least all the parts were there. David took all of the parts to Palmetto Rod Worx, also in Anderson, where the truck was going to be completed.

After piecing together the two different frames, the team at Palmetto Rod Worx boxed the whole thing with steel plate and fabricated a C-notch into the rear. The front of the frame was also Z’d for more room to lay out. With all of the cutting and grinding on the frame complete, it was painted gray for a clean look. For the suspension up front, David had a Mustang II clip bolted on with a set of Heidts drop spindles and control arms. Out back, a custom four-link was built to facilitate laying out the ol’ Ford. An Accuair air-ride system was installed along with a set of Slam Specialties RE-7 ‘bags and Gabriel shocks for a low, smooth ride. To wrap up the chassis, David enveloped a set of 20-inch Boss 338 wheels in BFGoodrich g-Force rubber, 245/35R20 up front and 265/35R20 out back.

With the frame complete, an engine and transmission could be installed. Forgoing installing the engine and transmission from his original F-100, David decided on a 460ci engine out of a ’72 Lincoln along with a Ford C6 transmission. To the engine, David bolted on a Weiand intake manifold, Holley carb, Moroso oil pan, and Griffin radiator for superior cooling. To crank out a few more ponies, the engine was bored to .030 over, the heads were ported and polished, and a Comp cam, and DUI distributor were installed. To brighten up the engine compartment, a set of Trick Flow valve covers, polished intake, and powdercoated water pump have been installed. The engine sends its power through the C6 to a Ford 9-inch in the rear outfitted with Richmond 3.50 gears. The engine expels the hot exhaust gasses through a set of L&L ceramic-coated headers, 3-inch tubing and MagnaFlow mufflers. The engine will sip gas from a 28-gallon stainless steel fuel cell that sits between the rear framerails.

Holley Carb | Performance Motor Parts

My 1 barrel motorcraft carb is broken beyond repair. What do I have to do to get a 2 barrel holley to work? An adapter? What about the linkage? Will it choke the car? Thanks.

you used to be able to get a adaptor from Clifford Performance..not sure anymore, might cost more than a new carb.. also check ebay.com for a used carb..

http://autos.groups.yahoo.com/group/6cylMustangsonly/

Carburetor Removal Video – Holley Carb Install & Tuning DVD The Rochester Quadrajet carburetor was found perched atop the engine of many a classic GM performance vehicle. The Q-Jet is a very capable but often misunderstood carb. This book, How to Rebuild and Modify Rochester Quadrajet Carburetors, seeks to lift the veil of mystery surrounding the Q-Jet and show owners how to tune and modify their carbs for maximum performance.

HOLLEY DEMON CARB (Fresno) - $150: HOLLEY DEMON 770 CFM CARB WITH FUEL LINE,,,,,$150 OBO ,,,,,,

HOLLEY//AED 950 CARB (South SD) - $475

How to Build & Power Tune Holley Carburetors

Chapter 4 Basic carburetor parts REPAIR KITS Genuine Holley repair kits are very comprehensive. Several aftermarket companies also make very good quality ...

Holley carburetors, manifolds & fuel injection, how to select, install, tune, repair, and modify Holley fuel sytem components for street and racing use

Carburetor passages can be tested by directing air or smoke through a piece of ... Holley Illustrated Parts & Specs Manual for Older Carburetor Models. ...

Holley carburetor handbook--4150 & 4160, selection, tuning & repair

Explains how automobile fuel systems work, and how to repair, adjust, or install a carburetor

How to hot rod small-block Mopar engines, high performance modifications for street and racing : covers all Mopar "A" engines, 1964-1992

4-Barrel Holley Carb The Holley four-barrel comes in two basic types—a vacuum secondary version and a double-pumper version. ...

Cooperative tractor catalog

Stewart Mfg. Corp., Chicago. 111. Stromberg Motor Devices Co., Chicago, 111. Touch Parts & Foundry Co., Alma, Mich. SUB-CARBURETORS Holley Carburetor Co., ...